Davie Roofline logo
Stucco hip-roof house halfway through a tile re-roof, with black self-adhered underlayment on one side and new terracotta barrel tile stacked along the ridge

Roof replacement and repair referrals · Davie, FL

Standing Seam Metal Roofs in Davie, FL

  • Installed cost: $9 to $16 per sq ft, which HomeGuide puts at $13,500 to $40,000 for an average roof
  • Days on the roof: 2 to 5+ in HomeGuide's guide; Angi's table gives metal 7 to 14
  • Panel thickness: most homes get 24- or 26-gauge, and hurricane-zone code sets 26-gauge as the floor for steel
  • Service life: 30 to 50+ years, and HomeGuide says the usual PVDF finishes carry warranties of 30 years or more

Davie Roofline sets up a call with a metal roofing contractor, so someone measures your roof and prices standing seam panels for it. The ranges above are national figures from cost guides, useful for a ballpark and nothing more; panel type, metal and finish move the final number. The real choices on a standing seam job are how the seams lock, how thick the metal is, how the clips hold it and what paint covers it.

Get a free roofing estimate

Free for homeowners, HOAs and property managers. One local contractor contacts you.

Standing Seam Systems for Davie Homes

Snap-lock standing seam steel panels in charcoal gray running from ridge to eave on a hip roof

Snap-Lock Panels

Snap-lock panels press together along the seam with no seaming tool, so they need the least labor. HomeGuide lists the trade-offs:

  • They need a roof pitch of 3:12 or steeper.
  • They are not as reliable as mechanically locked panels in high wind.
  • Nail-strip panels are the cheapest snap-lock type; they fasten through slotted holes instead of clips and wear early if nailed too tight.

Clip maker SFS adds that snap-lock systems can't use floating clips, which matters on long runs (see clips below).

Roofer seen from behind running an electric seaming tool along a double-lock standing seam on a metal roof

Mechanically Seamed Panels (Single and Double Lock)

On a mechanically seamed roof, the panel edges overlap and a seaming tool folds them together on site. A single lock folds once, a double lock folds again, and HomeGuide notes these panels suit low slopes and take more skill to install. In Broward's hurricane zone the code table lists architectural metal panels at a 2:12 minimum pitch, and standing seam systems that pass the ASTM E2140 water test may go as low as 1:12 (FBC Table 1515.2). That makes seamed panels the usual pick for the flatter back porch or addition.

Stack of standing seam metal panels of different widths with a tape measure laid across the ribs

Panel Gauge and Width

Lower gauge numbers mean thicker metal. HomeGuide's material prices by gauge:

  • 22-gauge: $5.00 to $9.00 per sq ft, for commercial or high-end homes
  • 24-gauge: $3.50 to $8.00, aimed at severe-weather climates
  • 26-gauge: $3.00 to $5.00, for mild to moderate climates
  • 29-gauge: $2.25 to $3.50, for small barns and sheds

In the High-Velocity Hurricane Zone, steel panels must be at least 26-gauge with G-90 coating, and aluminum at least 0.025 inch (FBC 1518.9). Panels run 12 to 24 inches wide; wider panels cost less but show more oil canning (a wavy look on flat metal), and thin metal shows it more.

Close view of concealed stainless clips fastened to underlayment between two standing seam panel ribs

Clip Systems: Fixed vs Floating

Clips hide under the seams and hold each panel to the deck. According to SFS:

  • A fixed clip doesn't let the panel move, so it suits shorter panels and costs less.
  • A floating clip lifts the panel slightly and lets it expand and contract with heat.
  • For panels longer than 30 feet, SFS says to strongly consider floating clips, and mechanically seamed panels can take either type.

The panel maker's own guidelines decide which clip is allowed, so ask the roofer which one the product approval lists.

Two painted metal roofing sample panels side by side, one deep bronze and one light gray, resting on a workbench outdoors

Paint Finishes: PVDF (Kynar) vs SMP

Most standing seam panels carry a PVDF finish such as Kynar 500 or Hylar 5000, which HomeGuide says is typically warrantied for at least 30 years. Silicone modified polyester (SMP) is the cheaper option. Metal supplier Sheffield Metals rates SMP a step below PVDF because it tends to chalk and fade sooner. SMP is harder and scratches less, its film adhesion warranty is often the same as PVDF, and Sheffield's price comparison, dated early 2022, put PVDF at about 60 to 80% more. That gap is a 2022 figure, so compare the two finishes on your own quote. Read the finish warranty: the fade and chalk terms are where the two differ.

Gloved hands lifting a terracotta barrel tile beside a metal valley flashing on a tile roof

Why Davie homeowners, HOAs and property managers call Davie Roofline

  • One request goes to one independent roofer, not a list of five
  • Ask for an inspection and a written scope before any deposit
  • Ask to see the product approval (NOA) number for every material quoted
  • Ask the roofer to name who pulls the Town of Davie permit
  • Hold the final payment until Davie's final inspection passes

Get a free roofing estimate

Free for homeowners, HOAs and property managers. One local contractor contacts you.

What Goes Into a Standing Seam Price

HomeGuide breaks a standing seam job into parts:

  • Metal

    installed prices run $7.50 to $12.50 per sq ft for Galvalume and $9.50 to $17.00 for aluminum, which HomeGuide calls ideal near the coast for its corrosion resistance.
  • Labor

    $5 to $8 per sq ft.
  • Tear-off

    $1 to $3+ per sq ft.
  • Decking

    replacing rotten sheathing adds $2 to $5 a sq ft; the roof deck replacement page covers rotted plywood and re-nailing.
  • Underlayment

    $0.10 to $0.90 per sq ft for a synthetic sheet under metal.
  • Custom colors

    about $1+ per sq ft more.

The Florida code requires a product approval for the complete metal system, panel, underlayment and accessories together (FBC 1518.9). Our tile roofing page explains Broward's hurricane-zone approvals, and the roof replacement page walks through the Town of Davie permit.

Questions to Put to the Roofer

  • Snap-lock or mechanically seamed, and single or double lock?
  • Which gauge and which metal, steel or aluminum?
  • Fixed or floating clips, and what spacing does the approval call for?
  • PVDF or SMP, and what do the fade and chalk terms of the finish warranty say?
  • Will panels be roll-formed on site? HomeGuide notes that on-site forming lets panels run any length, so there are fewer end seams.

For 5V crimp, stone-coated steel and the other metal profiles, see metal roofing. Barn and stable roofs are on the barn roofing page.

Ready to get started in Davie?

Request a free estimate