Davie Roofline logo
Stucco hip-roof house halfway through a tile re-roof, with black self-adhered underlayment on one side and new terracotta barrel tile stacked along the ridge

Roof replacement and repair referrals · Davie, FL

Soffit and Fascia Repair in Davie, FL

  • Typical eave repair: HomeGuide's average range is $500 to $2,600 for rotted fascia and soffit sections
  • Full soffit and fascia: $9 to $34 per linear foot, or $900 to $6,800 across the 100 to 200 feet most homes have
  • Fascia board alone: $5 to $12 per linear foot, with gutter removal and rehanging included
  • When to schedule it: HomeGuide says replacing soffit and fascia during a re-roof is the cheapest time, and the re-roof itself runs 1 to 8 days on site

Davie Roofline sends eave-repair requests on to a local roofing company. Ask for one price covering the rotten boards, the vents and the edge metal. Fascia work during a roof repair or replacement is part of a Florida roofing contractor's licensed scope. All of these numbers come from national cost guides, so they show the usual spread and your own eave sets the real figure.

Get a free roofing estimate

Free for homeowners, HOAs and property managers. One local contractor contacts you.

Soffit and Fascia Work on Davie Roofs

The eave is where the roof deck, the edge metal, the gutter and the attic vents all meet. These are the five jobs that come up there.

New white perforated aluminum soffit panels under the eave of a stucco house with a tile roof edge above

Vented Aluminum Soffit

Soffit is the underside of the overhang, and on a vented system it's also the attic's air intake. Price points from HomeGuide:

  • Soffit installed: $4 to $22 per linear foot (the top of that range is for 2-foot-wide soffit)
  • Continuous vented aluminum or vinyl soffit, material only: $0.50 to $2.00 per linear foot
  • Add-on soffit vents: $15 to $30 each, or $2.50 to $4.00 per foot for continuous strips

The Florida Building Code limits attic vent openings to between 1/16 and 1/4 inch at their smallest dimension. Anything wider needs corrosion-resistant screen to keep birds, rodents and snakes out. InterNACHI rates aluminum soffit and fascia at 20 to 40+ years.

Carpenter seen from behind on a ladder fitting a new primed wood fascia board where a rotted section was cut out

Wood Fascia Board Replacement

Fascia is the board along the rafter ends that carries the gutter and the drip edge. HomeGuide prices fascia replacement at $5 to $12 per linear foot installed, or $500 to $2,400 for a typical home, and that figure includes taking the gutters down and rehanging them. Wood is the most common fascia material, but HomeGuide notes it resists water worse than vinyl, composite or fiber cement. In the High-Velocity Hurricane Zone the code requires every eave to give the edge metal a firm nailable substrate, so a soft board has to go before new metal goes on.

Roofer seen from a distance bending a white aluminum wrap over a wood fascia board on a single-story stucco home

Aluminum Fascia Wrap

A wrap is a formed metal cover over the wood fascia. HomeGuide puts fascia capping at $3 to $4 per linear foot installed and says the metal layer shields the board from water. Wrapping a board that's already soft only hides the rot, so ask the roofer to probe the wood and replace bad sections first. The code counts fascia systems as metal roof profiles, so ask which product and thickness the bid uses.

Galvanized drip edge flashing fastened along a roof eave over new peel-and-stick underlayment, with the fascia below

Drip Edge and Eave Metal

Drip edge is the bent metal strip at the roof's edge that kicks water past the fascia. HomeGuide prices new drip edge at $1.50 to $3.00 per linear foot. In Broward, which sits in the High-Velocity Hurricane Zone, the code sets the shape:

  • Vertical face at least 1-1/2 inches, reaching at least 1/2 inch below the sheathing
  • Deck flange at least 2 inches wide, with a 1/2-inch kick clear of the building
  • Joints lapped at least 4 inches and sealed with approved flashing cement
  • Metal at least 26-gauge G-90 galvanized steel or 0.025-inch aluminum
  • On tile roofs, the tile has to overhang the drip edge by 3/4 inch to 2 inches
Attic interior with insulation pulled back from the eave, showing daylight through soffit vents and a clear air channel under the roof deck

Attic Ventilation at the Eaves

The Florida Building Code sets attic venting at 1/150 of the ventilated space's area, counted as net free vent area. That drops to 1/300 when 40 to 50% of it sits high on the roof, within 3 feet of the ridge, and the rest comes in at the eaves. The code also wants a 1-inch air gap between insulation and roof sheathing. HomeGuide notes that clearing insulation off the inside of soffit vents adds labor. In the hurricane zone, ridge vents need their own product approval and a wind-driven rain test, so ask for the approval number of any new vent.

Gloved hands lifting a terracotta barrel tile beside a metal valley flashing on a tile roof

Why Davie homeowners, HOAs and property managers call Davie Roofline

  • One request goes to one independent roofer, not a list of five
  • Ask for an inspection and a written scope before any deposit
  • Ask to see the product approval (NOA) number for every material quoted
  • Ask the roofer to name who pulls the Town of Davie permit
  • Hold the final payment until Davie's final inspection passes

Get a free roofing estimate

Free for homeowners, HOAs and property managers. One local contractor contacts you.

What Moves the Price of an Eave Repair

The linear-foot rates above are a starting point. HomeGuide lists what pushes a bid up or down:

  • Soffit width

    2-foot-wide soffit doubles the per-foot material and labor
  • Old material

    tear-out runs $1 to $2 per linear foot, often folded into labor
  • Painting

    soffit and fascia together run $4 to $14 per linear foot
  • Rot past the eave

    a structural engineer runs $100 to $220 an hour when decay reaches the rafters inside
  • Gutters

    new gutters add $12 to $25 per linear foot if the old ones don't go back up

Rotted rafter tails are a deck-and-framing job, so they're priced on the roof deck replacement page. New gutters are covered on the gutter installation page.

Fix the Eaves Before the New Roof Goes On

The roof edge locks over the fascia: underlayment laps the drip edge, and tile or shingle hangs past it. Replacing a rotten board after the roof is done means lifting that edge again. Ask for these lines in the re-roof bid:

  • A per-foot fascia price, so a bad board found at tear-off is already priced
  • Who removes and rehangs the gutters
  • The drip edge material and gauge
  • Whether soffit vents will be cleared or added to meet the code ratio

If the roof is coming off too, the Town permit and inspections are explained under roof replacement.

Ready to get started in Davie?

Request a free estimate