Davie Roofline logo
Stucco hip-roof house halfway through a tile re-roof, with black self-adhered underlayment on one side and new terracotta barrel tile stacked along the ridge

Roof replacement and repair referrals · Davie, FL

Barn Roofing in Davie, FL

  • Pole barn or garage: HomeGuide prices a metal roof on a 40' x 30' pole barn at $6,000 to $19,200 installed
  • Exposed-fastener panel: $500 to $1,200 per square (100 sq ft), or $5 to $12 per sq ft for corrugated sheet
  • Time on site: a metal roof replacement takes 1 to 5 days, per HomeGuide
  • Farm buildings: under Florida Statutes section 604.50, a nonresidential farm building (not one used as a home) on land used for bona fide agriculture, not urban agriculture, is exempt from the building code and local codes and fees, except floodplain rules

Davie Roofline introduces barn and stable owners to one local roofer for a quote on a stall barn, a shed row or a single run-in. The prices are national HomeGuide ranges for comparing bids, not a figure for your building. Below are the outbuilding types, what fastener wear looks like, and how the farm-building exemption works.

Get a free roofing estimate

Free for homeowners, HOAs and property managers. One local contractor contacts you.

Barn and Outbuilding Roofs in Davie

Wikipedia's entry on the town notes that horseback riding is common in Davie, with ranches among its historic buildings. These are the five outbuilding roof jobs a barn owner is likely to price.

Long center-aisle horse barn with a new silver metal roof and open stall doors, a fenced paddock and live oaks beside it

Horse Barns and Stall Rows

A stall barn is a long, simple roof with a lot of panel and a lot of screws. HomeGuide's gauge table matters most here:

  • 29-gauge: $1.00 to $3.00 per sq ft for material, listed for small barns or sheds in mild climates
  • 26-gauge: $1.50 to $5.00, residential roofs in mild to moderate climates
  • 24-gauge: $3.00 to $7.00, residential and commercial roofs where severe weather is common

Ask which gauge each bid uses and why, and compare that line first when two barn quotes don't match.

Small three-sided run-in shed with a single-slope metal roof in a grassy pasture with a horse grazing nearby

Run-In Sheds

A run-in is a three-sided shelter with a single-slope roof, and it's often the smallest job on a property. HomeGuide puts a metal roof on a 10' x 12' shed at $600 to $1,900 installed. Small roofs cost more per square foot because most contractors charge a minimum project fee, so it pays to have the run-in quoted with the barn.

Open-sided pole barn covering a sand riding arena, with a long-span metal roof on wood posts under a bright sky

Covered Arenas and Pole Barns

Pole barns and covered arenas are open-sided, with long roof spans on posts. HomeGuide's $6,000 to $19,200 range is for a 40' x 30' pole barn or garage. HomeGuide says cost depends on building size. Ask which wind risk category the roofer is designing to (the code speeds are below). On an open building, also ask whether the existing frame can carry the panel's required fastener pattern.

Close view of corrugated galvalume panels on a barn roof, rows of screws with washers running across each purlin line

Exposed-Fastener Metal Panels

HomeGuide calls galvanized or galvalume corrugated panels popular and budget-friendly for shed roofs. Exposed-fastener panels come as corrugated, ribbed or 5V crimp sheets screwed through the face. HomeGuide's numbers:

  • Corrugated or sheet metal: $5 to $12 per sq ft installed
  • Galvalume corrugated: $500 to $1,000 per square installed
  • Trade-off: cheaper and simpler than standing seam, but HomeGuide says exposed-fastener roofs need more maintenance and wear faster because every screw is a penetration

Standing seam and the full metal lineup for houses are on the metal roofing page.

Roofer seen from behind on a barn roof driving a new screw with a washer beside an old rusted one

Re-Screwing and Fastener Replacement

On a sound metal barn roof, the screws usually give out before the panels. SFS, a fastener manufacturer, says:

  • Each roofing screw seals with a rubber washer; drive it too deep and the washer bulges out and leaks
  • Screws that back out should be replaced with a type better matched to the job, not the same screw again
  • Screws over 20 years old are "on borrowed time," and most won't safely make it past 30

InterNACHI's life chart shows how much the screw coating matters: galvanized fasteners 10+ years, electro-galvanized 15 to 45, hot-dipped galvanized 35 to 60, stainless 65 to 100+. It rates the metal roof itself at 40 to 80 years. Ask what coating the replacement screws carry.

Gloved hands lifting a terracotta barrel tile beside a metal valley flashing on a tile roof

Why Davie homeowners, HOAs and property managers call Davie Roofline

  • One request goes to one independent roofer, not a list of five
  • Ask for an inspection and a written scope before any deposit
  • Ask to see the product approval (NOA) number for every material quoted
  • Ask the roofer to name who pulls the Town of Davie permit
  • Hold the final payment until Davie's final inspection passes

Get a free roofing estimate

Free for homeowners, HOAs and property managers. One local contractor contacts you.

Permits and the Farm-Building Exemption

Florida Statutes section 604.50 exempts a nonresidential farm building from the Florida Building Code and from county and municipal codes and fees, with the floodplain rules still in force. To qualify, the building has to be:

  • On land used for bona fide agricultural purposes, and not urban agriculture
  • Used mainly for agriculture, on land that's part of a farm operation or classified as agricultural under section 193.461
  • Not meant as a residence (the statute names barns, storage buildings and farm offices as examples)

A horse barn behind a house on a residential lot may not meet that test. Check how your parcel is classified before you skip a permit. Davie's roofing permit checklist asks for the Broward County Property Appraiser ownership printout, so that record is the place to start.

Wind and Product Rules When a Barn Isn't Exempt

A barn that doesn't qualify is roofed like any other building in Broward's High-Velocity Hurricane Zone:

  • Licensed work

    the code says all roofing work is done by a contractor licensed to perform roofing
  • Product approval

    every roofing component needs a valid, current product approval
  • Design wind

    156 mph for Risk Category I structures and 170 mph for Category II, so the panel, gauge and screw spacing have to match the category the building is designed to
  • Trim metal

    flashings and other accessories need the code minimum gauge (the soffit and fascia page lists the drip-edge metal rules)

Ask for the product approval numbers on the panel and the fastener in the written quote. For how a Davie roof permit runs, see roof replacement.

Frequently asked questions

My barn sits on agricultural land. Do I still pull a roofing permit?

Possibly not. Florida exempts a nonresidential farm building on land used for bona fide agricultural purposes from the building code and any county or municipal code or fee, though floodplain rules still apply. The exemption doesn't cover urban agriculture or a building used as a home, so check your parcel's agricultural classification before skipping the permit.

The barn roof drips at the screws after every storm. New roof or new screws?

Often new screws first. A fastener maker's guidance says screws over 20 years old are on borrowed time and most won't last past 30, and over-driven screws crush their rubber washers and leak. If the panels themselves are sound, ask for a re-screw quote with matched replacement fasteners next to a re-roof quote. Rusted-through panels change that answer.

Why did the quote for my little run-in shed come out so high per square foot?

Minimum charges: HomeGuide's shed price and the reason small roofs cost more per square foot are in the run-in section below. Having the shed quoted with a bigger barn or house job may get you past that minimum.

Is the thin 29-gauge panel from the farm store fine for a horse barn here?

Check it against HomeGuide's gauge table in the panel section below and Broward's code wind speeds in the code section. Ask the roofer which gauge and fastener spacing the barn's design wind load calls for.

Ready to get started in Davie?

Request a free estimate